• If you are citizen of an European Union member nation, you may not use this service unless you are at least 16 years old.

  • Whenever you search in PBworks or on the Web, Dokkio Sidebar (from the makers of PBworks) will run the same search in your Drive, Dropbox, OneDrive, Gmail, Slack, and browsed web pages. Now you can find what you're looking for wherever it lives. Try Dokkio Sidebar for free.


Drag (2013) (redirected from Drag (2015))

Page history last edited by Joe Redish 4 years, 1 month ago

Class content Kinds of Forces Resistive forces




When an object moves through a fluid, it feels a resistance to its motion for two reasons: (1) It is dragging the fluid along with it and making the fluid slide along itself, and the fluid has an internal resistance to doing that (viscosity); (2) It is pushing the fluid in front of it, making the fluid in front of it go with the same speed that it is going.  To do that the object has to exert a force on the molecules of fluid in the direction of motion, so, by Newton's 3rd law, the fluid molecules exert a force back on the object, opposite to the direction of motion.  This second force is called drag or sometimes inertial drag.   An object moving in a fluid always feels both of these, but depending on the various parameters of the situation, one can be much more important than the other.  The ratio of the drag force to the viscous force is called the Reynolds number and tells which of the two forces you have to pay attention to in a given situation.

Though motion in a fluid is a very complex process, we can get a pretty good idea of what the drag force looks like with a simple model.  Indeed, let's pick the simplest possible model to calculate: a cylinder moving through a fluid as shown in the figure at the left.  We have a cylinder of radius, R, moving in a direction along its axis with a speed v through a mass of molecules of density, ρ (rho).

We'll model this situation with the simplest model we can create.  We know the molecules in the fluid are jittering around at a very high speed.  But on the average, as many are going in the opposite direction as in any given direction.  We'll assume that on the average all the molecular jiggling cancels out.  The cylinder will be pushing molecules in front of it.  It therefore has to add speed to those molecules, making them move (on the average) the same speed as the cylinder is going.  So how much force does it have to exert to add speed to those molecules?


In a small amount of time, Δt, the cylinder will move a distance Δx = v Δt.  The front surface of the cylinder will therefore sweep out all the molecules in a thin volume equal to the area of the circle on top of the cylinder times Δx.  So it sweeps out a small volume ΔV = πR2 Δx.  The mass of molecules in this volume is this volume times the density, or Δm = ρΔV.  To add a change in velocity from 0 to v to this small mass, the the cylinder has to exert a force of

so putting in our whole chain of what we know about the distance and the mass


By Newton's 3rd law, the force the fluid exerts back on the cylinder is equal in magnitude and opposite to this:


So we conclude that the drag force that a fluid exerts on an object moving through it

  • opposes the motion
  • is proportional to the density of the fluid.
  • is proportional to the area being pushed through the fluid.
  • is proportional to the square of the velocity of the object through the fluid.


Now our model was pretty simplified.  We ignored the fact that the molecules of the fluid were moving, and we ignored the fact that they in fact had to go someplace -- they are being pushed into fluid ahead of the object so the fluid has to slide through itself.  The result of all this is summarized by putting in a dimensionless coefficient Cdrag -- the drag coefficient -- which is determined by measurement.  Typically, it is not very different from 1.  This is the equation we will use. (The factor of ½ has to do with the derivation of this law from momentum conservation and makes the interpretations of the coefficient more natural.*)

*Note that the drag coefficient can hide some complexity. But for a wide range of conditions and objects, it is in the neighborhood of "1" (that is, between 0.5 and 5.0). 




Joe Redish and Julia Gouvea 9/30/11



Comments (0)

You don't have permission to comment on this page.